Results 1 to 14 of 14

Thread: Wtb piece of starboard 4 gps install

  1. #1
    Join Date
    Feb 2009
    Location
    Chapin
    Posts
    6,787

    Default Wtb piece of starboard 4 gps install

    Removed a 10in garmin and replacing it with a simrad. The hole from the garmin is slightly larger than I need to I’ll be installing a piece of starboard if I can get my hands on some.

    Anybody got a piece laying around they want to sell? Would need to be big enough for a 12in simrad

    Located in chapin but I travel and could arrange a pickup
    Quote Originally Posted by Rebel Yell View Post
    now Hogan can fuck off on here all day and call it work, thanks!

  2. #2
    Join Date
    Jul 2015
    Location
    Columbia
    Posts
    145

    Default

    GE composites on shop road, columbia

  3. #3
    Join Date
    Feb 2009
    Location
    Chapin
    Posts
    6,787

    Default

    Quote Originally Posted by Bubbaweave View Post
    GE composites on shop road, columbia
    Thank you!
    Quote Originally Posted by Rebel Yell View Post
    now Hogan can fuck off on here all day and call it work, thanks!

  4. #4
    Join Date
    Dec 2006
    Location
    May River
    Posts
    7,338

    Default

    https://www.boatoutfitters.com/black-2025-acrylic-sheet

    For dash applications I like this. They cut to spec and do a damn good job.
    you aint did a dawg gon thang until ya STAND UP IN IT!- Theodis Ealey


    Quote Originally Posted by Rebel Yell View Post
    The older I get, the more anal retentive I get.

  5. #5
    Join Date
    Jan 2004
    Posts
    15,351

    Default

    Worst marine not carry any?
    Amendment II A well regulated Militia, being necessary to the security of a free State, the right of the people to keep and bear Arms, shall not be infringed.

    Quote Originally Posted by Highstrung View Post
    I like fishing topwater. Will one of you jot down some of this redneck ghetto slang and the definitions for those of us who weren't born with a plastic spoon in our mouths?

  6. #6
    Join Date
    Aug 2011
    Location
    Charleston
    Posts
    3,309

    Default

    I have some scrap white in the garage, it’s 1/2” I believe so it may be too thick.

  7. #7
    Join Date
    Aug 2011
    Location
    Charleston
    Posts
    3,309

    Default

    Quote Originally Posted by fro View Post
    https://www.boatoutfitters.com/black-2025-acrylic-sheet

    For dash applications I like this. They cut to spec and do a damn good job.
    Acrylic is nice for dash applications like this.

  8. #8
    Join Date
    Jun 2010
    Location
    charleston
    Posts
    8,600

    Default

    Poly cutting board from the housewares section works fine- cut with saw and round off corners/edges as desired. Restaurant supply house has it too- ours in Charleston (Berlins) usually has scraps large enough very cheap. Makes great boat bunk slides too.

  9. #9
    Join Date
    Dec 2010
    Posts
    28,018

    Default

    I bought two pieces last week at West Marine on Harbison for radar install
    They have plenty in white or black

  10. #10
    Join Date
    Aug 2008
    Location
    Sandy Run
    Posts
    2,759

    Default

    Us chef store on Saint Andrews. Large cutting boards cheap


    If a man is alone in the woods, says something, and a woman does not hear, is he still wrong?

    Bipartisan usually means that a larger-than-usual deception is being carried out. —George Carlin

    Common sense is not a gift. It's a punishment because you have to deal with everyone else who doesn't have it.

  11. #11
    Join Date
    Nov 2007
    Location
    Lexington, SC
    Posts
    14,522

    Default

    Quote Originally Posted by mello_collins View Post
    Us chef store on Saint Andrews. Large cutting boards cheap
    This was my first thought as well.
    Quote Originally Posted by ecu1984 View Post
    Steelin' Ducks is the KRT of suppressors and such.

  12. #12
    Join Date
    Dec 2010
    Posts
    28,018

    Default

    If Garmin is functional and interested in selling it, let me know.
    I have a 7 inch Lowrance now and have been thinking about a larger display
    I may be interested

  13. #13
    Join Date
    Aug 2011
    Location
    Charleston
    Posts
    3,309

    Default

    Careful on UV stability on the cutting boards.

  14. #14
    Join Date
    Dec 2006
    Location
    May River
    Posts
    7,338

    Default

    KIMG2485.JPG
    Blanked this worthless hole out with acrylic.
    you aint did a dawg gon thang until ya STAND UP IN IT!- Theodis Ealey


    Quote Originally Posted by Rebel Yell View Post
    The older I get, the more anal retentive I get.

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •